Leaderboard

These ‘ASOS DESIGN heeled chelsea boots in black faux leather with chain detail’ seemed to me to provide the right balance between enjoyment and discretion and I could no longer resist them when a double discount was on offer. I usually wear a UK11 or 12 and opted for 12 (securing the last pair, it seems) to allow thicker socks if needed. First impressions were favourable – a 3 5/8” heel, a zipped shaft taller than the online advert implied, and an almond toe. The fit was good and comfortable indoors. The ‘round’ heel may not appeal to some, but it is not really noticeable. Likewise, the gilt chain detail is perhaps rather too ‘blingy’, but could be removed. The hollow plastic heels were, as expected, rather noisy – and the plastic top pieces will obviously wear and need replacement. I decided to modify them before wearing them outdoors. The top pieces (held by four pegs) were carefully prised off and fitted with discs of 1/4" composition material, glued on. (I used a hole cutter, without its centre drill, to produce discs just a tad too large, which were then reduced and smoothed on my grinding wheel before glueing.) To dampen noise, I filled the hollow heels with compacted sawdust, with pieces of crimped drinking straw inserted temporarily into the peg holes to stop sawdust entering. The top pieces were then pressed in; the fit seems firm enough not to need any adhesive. The composition layer can of course be removed when worn and replaced. Adding the extra layer to the top piece has increased the heel height to 3 7/8”. The balance of the boots has not been affected; indeed, they sit rather better with the extra height. I wore them outside briefly with thick socks and bootcut jeans and they seem comfortable enough. The pics show the boots as received, as worn with bootcut jeans, and the stages of heel modification.

You are both correct! Yes, I have a vertical drill and it was duly used. I did prepare a guide by drilling through a piece of 6mm MDF with the holesaw, and then placing this on top of the composition material to 'centre' the holesaw (with its centre drill retracted) before cutting the required disc. Clamping was not necessary (although it might well be advisable to avoid 'snatching') and a little water was used as a cutting lubricant. If and when the extra top piece requires replacement, it should be possible to prise this off and simply glue another on. But, if the original plastic top piece fails (or the extra height created by the composition is unacceptable), I would fill the peg holes with dowel forced in and use brass panel pins to nail the new top piece into the dowels, reinforcing with suitable adhesive. Adding some wood forced into the hollow void before glueing and nailing would give a stronger job.

One trick for using a holesaw without the centre bit is to drill a hole in a piece of scrap wood, using the centre bit in the usual way. Then use this as a guide when drilling the wanted item. Ideally clamp the guide and wanted item together. Works perfectly in my experience.

This week's church OOTW. There is nothing notable about it, except for the fact that this is the first time this year I was able to wear sandals. It finally warmed up, but it's only temporary. By the end of the week, we're looking at lows uncomfortably close to the freezing mark. I felt like I wanted to wear tan sandals yesterday with wide legged trousers, but my first choice was at the extreme steep end of my wearable range. Due to some strenuous physical activity yesterday, I elected not to wear those, but went instead with what I call my "pageant" shoes. Their actual designation is Steve Madden Dezzzy (yes, that's with three z's), but their very high heel with thick platform reminds me of the pageant shoes that every southeast Asian girl wears in a beauty pageant. Of course the real pageant shoes usually have a somewhat thinner heel and an ever thicker platform, but you get the idea. I get a nearly 6 inch heel with less than 4 1/2" of steepness. My son just bought himself a motorbike, and here I am somewhat awkwardly posing on it, at his suggestion. No, I did not ride the thing in those heels. A few minutes later in real time---Now that I have actually loaded the photos, I notice that I wore a nearly identical outfit sometime last August, minus the tie. I think it's the same exact shirt, pants, and shoes. I guess you'll have that from time to time if you don't document things, and with outfits, I certainly don't.

Happy Palm Sunday, everyone. It sure was cold and rainy for the load-in yesterday. It was cold and less rainy for the load-out. I had to set my camera back in the garage so it wouldn't get wet. One thing about the major religious holidays is that church attendance is way up compared to normal. Next Sunday at Easter there is a chance we'll have a packed sanctuary, which I haven't seen in years. As an aside, my Jewish friend from the Twin Cities just sent me pictures of her Purim service, and it looked well attended also. She wasn't wearing heels, though! I didn't necessarily wear anything different than normal, but I did get caught up on ironing last week when I was sick, so my shirt and pants haven't seen the light of day for some time, even though they are not new. Also having not gotten much love lately (judging from the cobwebs I had to knock off of them) are my BCBGeneration Sassafras boots. I figured this was one of the last chances I'd have to wear them for the season. The only thing I really don't like about them is that they are really too big around for me, and an inch too tall by my estimation. I hadn't been walking for 8 days because of my illness, and I almost overdid it today. I walked 3 miles (in other boots) and wore these boots for about 4 hours directly after. My feet actually cramped up a little bit as I was trying to get the boots off.