Leaderboard

That's basically 2, 3, and 4 inch in my imperial mind. Part of the reason why I came up with the 94% calculation is because the Italian Heels chart did not quite make sense to me. In particular, why in size 40 do I have to have a full 11 cm to equal a 10 cm in size 38, but I only need 12.7 cm to equal 12? The proportions are all a little bit off. Therefore, I came up with my own. It may be that an 11 cm heel is what you get when you order a 10 cm heel in size 40 from them, but the math doesn't quite math. Oh yes, it absolutely does! To be fair, it has taken me over a decade to get to that point, but I didn't exactly take the short route when it came to training. If I were in the main office far away from any construction job site, I might consider wearing heels to work, but the far more likely scenario is that I'd be in the field office, the temporary office that is right there on the job site. Those folks often wear tennis shoes or casual loafers to work, and then have work boots and all the PPE there for the occasions where they might have to step foot on the actual job site. If I could guarantee that wearing heels in such a situation wouldn't negatively affect my job somehow, I'd do it, but I certainly can't guarantee that. Even the female superintendents and other supervisors would have a hard time wearing heels to the job without negative consequences. I did it in inches. USW size 9 is 9 7/8", which is the actual measurement of my size 9 foot. This is also typically given as an equivalent for EU size 40. Size 7 (or 38) is somewhere around 9 5/16". Looking at it again, the charts disagree with each other slightly, and depending upon how you round certain numbers, I came up with something like 94.3%, which I rounded down to 94. It seems some charts list size 9 as being 10" long. Your mileage may vary. Also why would I divide by 94% to convert something bigger to something smaller? I have the size 9 (40) in my hand. I can measure it. I do not have the size 7 (38) in my hand. Therefore, I need to multiply by 0.94 (or 0.95) to find out the information I need.

You guys must have or have had interesting jobs, I can't even really follow from the descriptions 🫢 How come that you would long to, but still wouldn't wear them? Good categorization, I also go with that! Is there actually a definition of stripper heels, or do you have a personal one? For me, the only type that comes to my mind are the ones with huge platforms and rather low heels (if you subtract the platform). Of course, join us if you want! I can also recommend trying something higher if you like the style. And yes, it really helps with lower heels too. I can feel the difference especially in something like a 11-12 cm heel, they became more comfortable for longer walks. Now that all the christmas markets and events are starting, I might as well try some higher ones for that and see how it goes. Not my new 13+ cm boots though, that would be too much. But I wear them everyday at home and it's getting better. I'm close to wearing them out for the first time.

Exactly (as I stated in the 'other' thread). UK timber is invariably sold in length increments of 300mm, which is close to the imperial foot that used to be the increment. 2.4m (7.87 feet) is a very common length and still often referred to as an '8 foot' - but don't complain if it isn't quite that long when making something! UK Practice does vary. It seems that '4 x 2' is very commonly used (and I favour that), but some chippies and most timber merchants would refer to or list it as '2 x 4'. The latter is logical in that a whole range of timber used for rafters, joists, studwork etc is a nominal 2" thick but varies in width from a nominal 2" to 8" or more, so typically listed as '2 x 4, 2 x 5, 2 x 6' etc (or nowadays by the metric equivalents: 47 x 96 etc). But any builder or carpenter will know what is meant by a '2 x 4' (or a '4 x 2'!) even if he never worked in imperial measurements. 'Plasterboard' is the usual term for the generic product (as we have at least three major UK manufacturers) but some older folk call it 'Gyproc', which is the trade name used (though not now very prominently) by the oldest supplier - British Gypsum. You will sometimes hear the installers called 'dry wallers', but that is not really correct as plasterboard was originally introduced as a means of boarding ceilings - walls came later! It is more usual to call the installer a 'plasterer' (if he also skims the boards) but plasterboard is often installed by general builders or carpenters; it is not really a skilled task. Boards often have tapered edges (filled with plaster filler over paper or mesh tape - another relatively unskilled task) rather than square (flush) edges which need tape and a full skim-over, which is where the proper plastering skills come in.